IRTrans Support Forum

I have to hold power button on my remote for about 1-1.5 sec to switch TV ON or OFF
How do I learn this continuous code?

I tried to lean in repeat mode but it doesn't work.

and what is the "learn tooglecodes"? I didn't find anything about it in the manual.
If I try to learn in "learn tooglecodes" mode I see "IR error - Couldn't recored toogle command (No commans yet learned?)" What does it mean?

PS Irtrans Ethernet, Irserver ( windows)

Hi,
you can learn this IR codes using the option "Learn long button press" in the GUI client.

Toggle codes are a very special feature not needed here.

IRTrans

"Lange FB Tastendrucke lernen" - is this option in GUI client?? Why it is in German? (I have downloaded English version from you site)

How do I learn code with this checkbox on? If I press the button on my remote for a little - the code doesn-t work

If I press button for 1 sec I see error
Result [95-2] IR Error: IR code lenght>max.lenght - Code might not work

I use "Learn normal"

A look to rem file and didn't see the difference beetwin [on] and [on_long]. In the second case I checked the option for long codes.

[REMOTE]
[NAME]panasonic

[TIMING]
[0][N]3[1]3480 1736[2]504 360[3]504 1232[RC]3[FL]126[FREQ]38[SB][RS]

[COMMANDS]
[ch 01][T]0[D]S0100000000000100000000010000000000001000000010010
[ch 02][T]0[D]S0100000000000100000000010000000010001000100010010
[vol +][T]0[D]S0100000000000100000000010000000000000100000001010
[vol -][T]0[D]S0100000000000100000000010000000010000100100001010
[on/off][T]0[D]S0100000000000100000000010000000010111100101111010
[on][T]0[D]S0100000000000100000000010000000010111100101111010
[on_long][T]0[D]S0100000000000100000000010000000010111100101111010

"Lange FB Tastendrucke lernen" is the correct option. Looks like it has not been translated.

Maybe your IRTans device (Firmware version) does not support that option.

Which Firmware version does your IRTrans device have ?

IRTrans

E6.05.50

I tried RAW mode and it works:) While learning I press the button for about 1 sec

[REMOTE]
[NAME]panasonic

[TIMING]
[2][N]4[1]496 376[2]440 1288[3]3480 1728[4]496 73936[RC]1[RP]0[FREQ]38

[COMMANDS]
[on_raw@][T]2[D]000000000100000000010000000010111100101111013201000000000001000000000100000000101111001011110132010000000000010000000001000000001011110010111101320100000000000100000000010000000010111100101111013201000000000001000000000100000000101111001011110132010000000000010000000001000000001011110010111101320100000000000100000000010000000010111100101111010

The code you have posted above is no RAW code.

Anyways, it works so you should be fine.

IRTrans

Try this
[REMOTE]
[NAME]Panasonic

[TIMING]
[0][N]3[1]3440 1856[2]336 536[3]344 1408[RC]1[RP]0[FREQ]39[SB]

[COMMANDS]
[Power_toggle][T]0[D]S0100000000000100000000010000000010111100101111010
[Power_on][T]0[D]S0100000000000100000000010000000001111100011111010
[Power_off][T]0[D]S0100000000000100000000010000000011111100111111010

IRTrans Support Forum

Learning IR codes for Panasonic TV (ON/OFF)

Learning IR codes for Panasonic TV (ON/OFF)

Re: Learning IR codes for Panasonic TV (ON/OFF)

Re: Learning IR codes for Panasonic TV (ON/OFF)

Re: Learning IR codes for Panasonic TV (ON/OFF)

Re: Learning IR codes for Panasonic TV (ON/OFF)

Re: Learning IR codes for Panasonic TV (ON/OFF)

Re: Learning IR codes for Panasonic TV (ON/OFF)

Re: Learning IR codes for Panasonic TV (ON/OFF)