Learn IR codes with timing and RAW codes

Everything related to learning and capturing of IR Codes

Moderator: marcus

Learn IR codes with timing and RAW codes

Postby azauhar » Fri 20. Jul 2012, 10:51

When I learn codes with IRTrans in "RAW mode" my file looks like this:

[REMOTE]
[NAME]grundig_rcgd1_raw

[TIMING]
[0][N]0[RC]2[FL]107[FREQ]36[RC5]

[COMMANDS]
[power@][T]0[D]11000000001100
[1@][T]0[D]11000000000001
[mute@][T]0[D]11000000001101
[2@][T]0[D]11000000000010

It seems to me that it is not the RAW format. When I set to learn the codes with timing, that file looks like this:

[REMOTE]
[NAME]grundig_rcgd1_timing

[TIMING]


[COMMANDS]
[power][RAW]49[FREQ]38[D]784 888 800 880 1624 888 784 888 792 888 784 896 792 880 792 888 792 1728 784 896 1624 888 792 0 328 1472 792 888 784 896 1624 880 792 888 792 888 784 888 792 888 792 888 792 1728 784 896 1616 888 864
[mute][RAW]49[FREQ]38[D]792 888 1624 888 784 888 792 888 792 888 792 880 792 888 792 888 784 1736 792 880 1632 1728 784 0 328 640 792 888 1616 888 792 888 792 888 792 880 792 888 792 888 784 888 800 1728 784 888 1624 1736 848
[1][RAW]53[FREQ]38[D]792 888 784 888 1616 896 792 888 792 880 792 888 784 896 784 888 800 880 792 888 784 888 792 1728 800 0 328 656 792 888 792 888 1624 880 792 888 792 888 784 888 800 880 792 888 792 880 792 888 784 896 792 1728 856

It seem to me that this is the RAW format, so those two types of recording IR codes are maybe switched in IRTrans Software?

Thank you for your answer!
azauhar
 
Posts: 20
Joined: Wed 18. Jul 2012, 10:40

Re: Learn IR codes with timing and RAW codes

Postby IRTrans » Fri 20. Jul 2012, 12:44

Hi,
the codes in the first example are repeat codes. The codes in the 2nd example are RAW codes.

Which version of the GUI Client did you use to learn the codes?

IRTrans
IRTrans
Administrator
 
Posts: 2115
Joined: Mon 21. Apr 2008, 23:32

Re: Learn IR codes with timing and RAW codes

Postby azauhar » Mon 23. Jul 2012, 08:52

I used some older version, I am not sure which because I uninstalled it before I saw your post here, but then I installed the latest version of IRTrans software and the same thing is happening.

I also saw that some other IRTrans user had the same problem with recording his codes. See the bottom of his thread bellow:

http://www.irtrans.de/forum/viewtopic.p ... 6kHz#p6376
azauhar
 
Posts: 20
Joined: Wed 18. Jul 2012, 10:40

Re: Learn IR codes with timing and RAW codes

Postby IRTrans » Mon 23. Jul 2012, 11:15

We will try that again. However, from what I have seen in the other thread we had tried it then, too and it worked.

Please make sure you are using the GUI Client for learning and not the very old IRTransTray.exe.

IRTrans
IRTrans
Administrator
 
Posts: 2115
Joined: Mon 21. Apr 2008, 23:32

Re: Learn IR codes with timing and RAW codes

Postby IRTrans » Mon 23. Jul 2012, 11:19

I just tried it and it is working correctly.

Please make sure that you set the option in the GUI Client before you start learning.

IRTrans
IRTrans
Administrator
 
Posts: 2115
Joined: Mon 21. Apr 2008, 23:32

Re: Learn IR codes with timing and RAW codes

Postby azauhar » Mon 23. Jul 2012, 13:48

I tried it with GUI Client and with IRTransTray.exe and they are both doing that same mistake.
azauhar
 
Posts: 20
Joined: Wed 18. Jul 2012, 10:40

Re: Learn IR codes with timing and RAW codes

Postby IRTrans » Mon 23. Jul 2012, 14:27

If you are using irtranstray.exe you are not using the current SW. In the current SW irtranstray.exe has been replaced by IRTransServer.exe.
Please check all SW versions and make sure that you have selected the learn option before you click on "Learn".

Which Learn option do you exactly use?

Furthermore please let us know the SW/FW versions of all components (irserver.exe, GUIClient.exe, IRTrans Firmware).

IRTrans
IRTrans
Administrator
 
Posts: 2115
Joined: Mon 21. Apr 2008, 23:32

Re: Learn IR codes with timing and RAW codes

Postby azauhar » Wed 25. Jul 2012, 09:56

Sorry, I wrote the wrong thing in the previous post. I am using IRTrans server, not IRTrans tray.

When I select option "Learn command with timing" i get RAW codes. When I select option "RAW mode" the I get codes with timing.

Here are the versions of my SW/FW:
IR server - v6.09.04
GUI Client - v7.2.1.29680
IRTrans Firmware - v3.8
azauhar
 
Posts: 20
Joined: Wed 18. Jul 2012, 10:40

Re: Learn IR codes with timing and RAW codes

Postby IRTrans » Wed 25. Jul 2012, 11:00

Hi.
V3.8 is the HW Version of your IRTrans device. On the device status dialog or in the log file / diagnostics after start of the irserver you can see the FW version of your device.

Furthermore please switch the IRTransserver log to loglevel 4 and post the resulting log when learning an IR code.

IRTrans
IRTrans
Administrator
 
Posts: 2115
Joined: Mon 21. Apr 2008, 23:32

Re: Learn IR codes with timing and RAW codes

Postby azauhar » Wed 25. Jul 2012, 12:29

IRTrans IR Control System Version 2.0.10.29680

I put loglevel 4 and recorded power and mute code in RAW mode. Here is the log from diagnostics:

IRServer Version 6.09.04
[ 0]: IRTrans USB U6.08.30 SN: 59116
Send Status 8 - 8 [0]
Netcommand Size: 112/112
Netcommand: 53 [0]
Send Status 3536 - 3536 [18]
Netcommand Size: 112/112
Netcommand: 18 [0]
Getremotes 0
Send Status 3536 - 3536 [6]
Netcommand Size: 112/112
Netcommand: 16 [0]
Send Status 307 - 307 [5]
Netcommand Size: 112/112
Netcommand: 2 [0]
Send Status 8 - 8 [0]
Netcommand Size: 112/112
Netcommand: 16 [0]
Send Status 307 - 307 [5]
Netcommand Size: 112/112
Netcommand: 9 [0]
IRTRans Send Done: 1
TIME CNT: 0
TIME : 0 0 0
TIME : 1 0 0
TIME : 2 0 0
TIME : 3 0 0
TIME : 4 0 0
TIME : 5 0 0
TIME : 6 0 0
TIME : 7 0 0
T.REP : 107
REP/MODE: 130 4
FREQ : 36
DATA : 11000000001100
LEN : 14
ADR : 0
MASK : 0
Total Code Len: 132 ms
Send Status 8 - 8 [0]
Netcommand Size: 112/112
Netcommand: 16 [0]
Send Status 307 - 307 [5]
Netcommand Size: 112/112
Netcommand: 9 [0]
IRTRans Send Done: 1
TIME CNT: 0
TIME : 0 0 0
TIME : 1 0 0
TIME : 2 0 0
TIME : 3 0 0
TIME : 4 0 0
TIME : 5 0 0
TIME : 6 0 0
TIME : 7 0 0
T.REP : 107
REP/MODE: 130 4
FREQ : 36
DATA : 11000000001101
LEN : 14
ADR : 0
MASK : 0
Total Code Len: 132 ms
Send Status 8 - 8 [0]
Netcommand Size: 112/112
Netcommand: 16 [0]
Send Status 307 - 307 [5]
Netcommand Size: 112/112
Netcommand: 5 [0]
**** CCF Error: ac1 [Remote: ccf.rem]
Remote ccf compiled: 20 Timings - 20 Commands
Remote dbox2 compiled: 1 Timings - 26 Commands
Remote denon-dvd compiled: 2 Timings - 52 Commands
Remote dream compiled: 0 Timings - 36 Commands
Remote grundig_raw_mode compiled: 1 Timings - 3 Commands
Remote grundig_rcgd1 compiled: 2 Timings - 36 Commands
Remote grundig_rcgd1_norm_timing compiled: 0 Timings - 15 Commands
Remote grundig_rcgd1_raw compiled: 1 Timings - 9 Commands
Remote grundig_rcgd1_raw2 compiled: 3 Timings - 3 Commands
Remote grundig_test compiled: 0 Timings - 5 Commands
Remote irtrans compiled: 1 Timings - 33 Commands
Remote kathrein-ufs compiled: 2 Timings - 36 Commands
Remote mce-keyboard compiled: 1 Timings - 77 Commands
Remote mce-mouse compiled: 1 Timings - 1 Commands
Remote mediacenter compiled: 1 Timings - 49 Commands
Remote motorola_norm_timing_orig compiled: 0 Timings - 21 Commands
Remote pace compiled: 2 Timings - 38 Commands
Remote philips_mcm393 compiled: 1 Timings - 17 Commands
Remote premiere compiled: 0 Timings - 36 Commands
Remote raw_mode compiled: 1 Timings - 2 Commands
Remote samsung_bn59_lcd compiled: 1 Timings - 21 Commands
Remote sky-digital compiled: 1 Timings - 31 Commands
Remote sky-hd compiled: 1 Timings - 34 Commands
Remote sonavis-keyboard compiled: 1 Timings - 88 Commands
Remote test_raw compiled: 1 Timings - 1 Commands
Remote test_raw2 compiled: 1 Timings - 3 Commands
Remote western_digital compiled: 1 Timings - 10 Commands
Duplicate Commands for ccf.0.0: grundig_rcgd1.0
Duplicate Commands for ccf.1: ccf.2 ccf.3 ccf.4
Duplicate Commands for ccf.2: ccf.3 ccf.4
Duplicate Commands for ccf.3: ccf.4
Duplicate Commands for grundig_rcgd1.power: test_raw2.power
Duplicate Commands for pace.0: pace.0-
Duplicate Commands for philips_mcm393.on-tuner: philips_mcm393.on-tuner1 philips_mcm393.tuner
Duplicate Commands for philips_mcm393.on-tuner1: philips_mcm393.tuner
Duplicate Commands for philips_mcm393.ch+: philips_mcm393.up
Duplicate Commands for philips_mcm393.ch-: philips_mcm393.down
Duplicate Commands for philips_mcm393.play: philips_mcm393.pause
Duplicate Commands for western_digital.play: western_digital.pause
Total: 27 Remotes - 47 Timings - 703 Commands - 0 Calib. Commands
0 Togglec. - 19 CCF Data - 0 CCF RAW - 1 CCF Error
Send Status 8 - 8 [0]
azauhar
 
Posts: 20
Joined: Wed 18. Jul 2012, 10:40

Next

Return to Learning of IR Codes

Who is online

Users browsing this forum: No registered users and 8 guests

cron